Blum Tandem cutlery tray, 1000mm unit, plastic, grey

A plastic cutlery insert for a 1000mm wide Blum Tandem drawer. 914x422mm, grey.

Blum Tandem cutlery tray, 900mm unit, plastic, grey (picture shows tray for 1000mm unit)

A plastic cutlery insert for a 900mm wide Blum Tandem drawer. 814x422mm, grey.

Blum Tandem cutlery tray, 800mm unit, plastic, grey (picture shows tray for 1000mm unit)

A plastic cutlery insert for an 800mm wide Blum Tandem drawer. 714x422mm, grey.

Blum Tandem cutlery tray, 600mm unit, plastic, grey (picture shows tray for 1000mm unit)

A plastic cutlery insert for a 600mm wide Blum Tandem drawer. 514x422mm, grey.

Blum Tandem cutlery tray, 500mm unit, plastic, grey (picture shows tray for 1000mm unit)

A plastic cutlery insert for a 500mm wide Blum Tandem drawer. 414x422mm, grey.

Blum Tandem cutlery tray, 400mm unit, plastic, grey (picture shows tray for 1000mm unit)

A plastic cutlery insert for a 400mm wide Blum Tandem drawer. 314x422mm, grey.

Knife block
Suitable for cutlery insert codes 556.53.550/560/580/590/600
Lacquered beech plywood

Cutlery insert with plastic lip around the edge 240mm wide, lip can be cut to a minimum of 200mm wide, 485mm deep again lip can be cut to a minimum of 440mm deep. Height 50cm.
With 2 x horizontal cutlery compartments at the top and 1 x verticle compartment at the bottom
2.5 mm thick plastic
silver grey high gloss finish
For use in 300mm wide cabinet 600mm deep

Cutlery insert with plastic lip around the edge 340mm wide, lip can be cut to a minimum of 300mm wide, 485mm deep again lip can be cut to a minimum of 440mm deep. Height 50cm.
With 4 x horizontal compartments
2.5 mm thick plastic
silver grey high gloss finish
For use in 400mm wide cabinet 600mm deep

Cutlery insert with plastic lip around the edge for 300mm units. 2 large & 1 small compartments
silver grey high gloss finish

Cutlery insert with plastic lip around the edge 390mm wide, lip can be cut to a minimum of 350mm wide, 485mm deep again lip can be cut to a minimum of 440mm deep. Height 50cm.
With 1x vertical compartment on the left hand side and 4 x horizontal on the right hand side
2.5 mm thick plastic
silver grey high gloss finish
For use in 450mm wide cabinet 600mm deep

Cutlery insert with plastic lip around the edge 440mm wide, lip can be cut to a minimum of 400mm wide, 485mm deep again lip can be cut to a minimum of 440mm deep. Height 50cm.
With 1x vertical compartment on the right hand side and 4 x horizontal on the left hand side
2.5 mm thick plastic
silver grey high gloss finish
For use in 500mm wide cabinet 600mm deep

Cutlery insert with plastic lip around the edge 540mm wide, lip can be cut to a minimum of 500mm wide, 485mm deep again lip can be cut to a minimum of 440mm deep. Height 50cm.
With 1x vertical compartment each side with 4 x horizontal compartments in the middle
2.5 mm thick plastic
silver grey high gloss finish
For use in 600mm wide cabinet 600mm deep

Cutlery insert with plastic lip around the edge 740mm wide, lip can be cut to a minimum of 700mm wide, 485mm deep again lip can be cut to a minimum of 440mm deep. Height 50cm.
With 3 x vertical compartments 1 on the left and 2 on the right with 4 x horizontal compartments in the middle
2.5 mm thick plastic
silver grey high gloss finish
For use in 800mm wide cabinet 600mm deep

Cutlery insert with plastic lip around the edge 840mm wide, lip can be cut to a minimum of 800mm wide, 485mm deep again lip can be cut to a minimum of 440mm deep. Height 50cm.
With 4 x vertical compartments 1 on the left and 3 on the right with 4 x horizontal compartments in the middle
2.5 mm thick plastic
silver grey high gloss finish
For use in 900mm wide cabinet 600mm deep

Cutlery insert with plastic lip around the edge 940mm wide, lip can be cut to a minimum of 900mm wide, 485mm deep again lip can be cut to a minimum of 440mm deep. Height 50cm.
With 5 x vertical compartments 2 on the left and 3 on the right with 4 x horizontal compartments in the middle
2.5 mm thick plastic
silver grey high gloss finish
For use in 1000mm wide cabinet 600mm deep

Divider 11mm thick 424mm deep
For use with multi-purpose inserts codes 556.54.540/545/550/560
Lacquered beech

Multi-purpose insert with a plastic lip around 340mm wide, lip can be ciut to a minimum of 300mm, 485mm deep again can be cut to a minimum of 440mm deep. Height 50cm.
No compartments in this tray, use dividers to make up compartments if required (dividers ordered seperately on 556.54.319). Dividers can be positioned as required.
2.5 mm thick plastic
Silver grey high gloss finish
For cabinet size 400mm Wide

Multi-purpose insert with a plastic lip around 390mm wide, lip can be ciut to a minimum of 350mm, 485mm deep again can be cut to a minimum of 440mm deep. Height 50cm.
No compartments in this tray, use dividers to make up compartments if required (dividers ordered seperately on 556.54.319). Dividers can be positioned as required.
2.5 mm thick plastic
Silver grey high gloss finish
For cabinet size 450mm Wide

Multi-purpose insert with a plastic lip around 440mm wide, lip can be ciut to a minimum of 400mm, 485mm deep again can be cut to a minimum of 440mm deep. Height 50cm.
No compartments in this tray, use dividers to make up compartments if required (dividers ordered seperately on 556.54.319). Dividers can be positioned as required.
2.5 mm thick plastic
Silver grey high gloss finish
For cabinet size 500mm Wide

Multi-purpose insert with a plastic lip around 540mm wide, lip can be ciut to a minimum of 500mm, 485mm deep again can be cut to a minimum of 440mm deep. Height 50cm.
No compartments in this tray, use dividers to make up compartments if required (dividers ordered seperately on 556.54.319). Dividers can be positioned as required.
2.5 mm thick plastic
Silver grey high gloss finish
For cabinet size 600mm Wide

Two-tier cutlery insert
Bottom tray has a plastic lip around that is 440mm wide and can be cut to a minimum of 390mm,485mm deep and again can be cut to 435mm.
Top tray is 363mm Wide and 423mm deep
ball bearing runners
2.5 mm thick plastic
White lined finish
For cabinet 500mm wide, 600mm deep

Cutlery insert cream-white 440-480mm deep, cab 400mm textured
With a generous border allowance for trimming to size
Once trimmed the insert will fit in cabinets with depths less than 600 mm
This material is too sturdy to cut with just scissors or a sharp knife
3 mm thick plastic
Cream-white textured moulded plastic

Cutlery insert cream-white 440-480mm deep, cab 450mm textured
With a generous border allowance for trimming to size
Once trimmed the insert will fit in cabinets with depths less than 600 mm
This material is too sturdy to cut with just scissors or a sharp knife
3 mm thick plastic
Cream-white textured moulded plastic

Cutlery insert cream-white 440-480mm deep, cab 500mm textured
With a generous border allowance for trimming to size
Once trimmed the insert will fit in cabinets with depths less than 600 mm
This material is too sturdy to cut with just scissors or a sharp knife
3 mm thick plastic
Cream-white textured moulded plastic

Cutlery insert cream-white 440-480mm deep, cab 600mm textured
With a generous border allowance for trimming to size
Once trimmed the insert will fit in cabinets with depths less than 600 mm
This material is too sturdy to cut with just scissors or a sharp knife
3 mm thick plastic
Cream-white textured moulded plastic

Plywood drawers sides 90mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:239 x 90 x 430mm long FOR A CABINET 300mm WIDE

Plywood drawers sides 90mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:339 x 90 x 430mm long FOR A CABINET 400mm WIDE

Plywood drawers sides 90mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:389 x 90 x 430mm long FOR A CABINET 450mm WIDE

Plywood drawers sides 90mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:439 x 90 x 430mm long FOR A CABINET 500mm WIDE

Plywood drawers sides 90mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:539 x 90 x 430mm long FOR A CABINET 600mm WIDE

Plywood drawers sides 140mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:339 x 140 x 430mm long FOR A CABINET 400mm WIDE

Plywood drawers sides 140mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:439 x 140 x 430mm long FOR A CABINET 500mm WIDE

Plywood drawers sides 140mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:539 x 140 x 430mm long FOR A CABINET 600mm WIDE

Plywood drawers sides 140mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:739 x 140 x 430mm long FOR A CABINET 800mm WIDE

Plywood drawers sides 140mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:939 x 140 x 430mm long FOR A CABINET 1000mm WIDE

Plywood drawers sides 90mm high
Dowel construction, for cabinets with 16 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:243 x 90 x 430mm long FOR A CABINET 300mm WIDE

Plywood drawers sides 90mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:343 x 90 x 430mm long FOR A CABINET 400mm WIDE

Plywood drawers sides 90mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:393 x 90 x 430mm long FOR A CABINET 450mm WIDE

Plywood drawers sides 90mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:443 x 90 x 430mm long FOR A CABINET 500mm WIDE

Plywood drawers sides 90mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:543 x 90 x 430mm long FOR A CABINET 600mm WIDE

Plywood drawers sides 140mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:343 x 140 x 430mm long FOR A CABINET 400mm WIDE

Plywood drawers sides 140mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:443 x 140 x 430mm long FOR A CABINET 500mm WIDE

Plywood drawers sides 140mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:543 x 140 x 430mm long FOR A CABINET 600mm WIDE

Plywood drawers sides 140mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:743 x 140 x 430mm long FOR A CABINET 800mm WIDE

Plywood drawers sides 140mm high
Dowel construction, for cabinets with 18 mm board thickness
Individually flat-packed with 3.2 mm fibre-board base
All sides are 12 mm plywood birch, stained and lacquered
These drawers have been especially designed for use with the roller runner 423.68.445
see end of section. Drawer size:943 x 140 x 430mm long FOR A CABINET 1000mm WIDE

Solid beech drawers, sides 100mm high, cab 300mm
Dowel and screw construction
Supplied flat-packed with plywood base and fixing screws
The special feature of these drawers is that the centre dowel of the 3 dowels on the back and front walls is drilled to accept the fixing screws which are inserted through the countersunk holes in the side walls into the hollow dowels. This gives added strength and stability to the drawer
Drawers have chamfered edges and a sanded and varnished finish

Solid beech drawers, sides 100mm high, cab 400mm
Dowel and screw construction
Supplied flat-packed with plywood base and fixing screws
The special feature of these drawers is that the centre dowel of the 3 dowels on the back and front walls is drilled to accept the fixing screws which are inserted through the countersunk holes in the side walls into the hollow dowels. This gives added strength and stability to the drawer
Drawers have chamfered edges and a sanded and varnished finish

Solid beech drawers, sides 100mm high, cab 450mm
Dowel and screw construction
Supplied flat-packed with plywood base and fixing screws
The special feature of these drawers is that the centre dowel of the 3 dowels on the back and front walls is drilled to accept the fixing screws which are inserted through the countersunk holes in the side walls into the hollow dowels. This gives added strength and stability to the drawer
Drawers have chamfered edges and a sanded and varnished finish

Solid beech drawers, sides 100mm high, cab 500mm
Dowel and screw construction
Supplied flat-packed with plywood base and fixing screws
The special feature of these drawers is that the centre dowel of the 3 dowels on the back and front walls is drilled to accept the fixing screws which are inserted through the countersunk holes in the side walls into the hollow dowels. This gives added strength and stability to the drawer
Drawers have chamfered edges and a sanded and varnished finish

Solid beech drawers, sides 100mm high, cab 600mm
Dowel and screw construction
Supplied flat-packed with plywood base and fixing screws
The special feature of these drawers is that the centre dowel of the 3 dowels on the back and front walls is drilled to accept the fixing screws which are inserted through the countersunk holes in the side walls into the hollow dowels. This gives added strength and stability to the drawer
Drawers have chamfered edges and a sanded and varnished finish

Solid beech drawers, sides 140mm high, cab 400mm
Dowel and screw construction
Supplied flat-packed with plywood base and fixing screws
The special feature of these drawers is that the centre dowel of the 3 dowels on the back and front walls is drilled to accept the fixing screws which are inserted through the countersunk holes in the side walls into the hollow dowels. This gives added strength and stability to the drawer
Drawers have chamfered edges and a sanded and varnished finish

Solid beech drawers, sides 140mm high, cab 500mm
Dowel and screw construction
Supplied flat-packed with plywood base and fixing screws
The special feature of these drawers is that the centre dowel of the 3 dowels on the back and front walls is drilled to accept the fixing screws which are inserted through the countersunk holes in the side walls into the hollow dowels. This gives added strength and stability to the drawer
Drawers have chamfered edges and a sanded and varnished finish

Solid beech drawers, sides 140mm high, cab 800mm
Dowel and screw construction
Supplied flat-packed with plywood base and fixing screws
The special feature of these drawers is that the centre dowel of the 3 dowels on the back and front walls is drilled to accept the fixing screws which are inserted through the countersunk holes in the side walls into the hollow dowels. This gives added strength and stability to the drawer
Drawers have chamfered edges and a sanded and varnished finish

Solid beech drawers, sides 140mm high, cab 1000mm
Dowel and screw construction
Supplied flat-packed with plywood base and fixing screws
The special feature of these drawers is that the centre dowel of the 3 dowels on the back and front walls is drilled to accept the fixing screws which are inserted through the countersunk holes in the side walls into the hollow dowels. This gives added strength and stability to the drawer
Drawers have chamfered edges and a sanded and varnished finish

Drawer under built under oven housing
Fits beneath a built-in oven, utilising the bottom of the cabinet and the plinth
For 600 mm cabinet width
Runners are completely concealed beneath the drawer base and cannot be seen when fully extended
• Runners are for 19 mm board thickness, plastic spacers are included for other board thicknesses
• Set consists of:
- Drawer (1 pc)
Aluminium/grey coloured plastic, designed to accept 8 mm chipboard base if required
- Dynamic runners (1 pair)
Galvanised steel, self closing, includes soft close mechanism, load capacity 25 kg
Drawer front fixing brackets (2 pcs)
White plastic, screw fixed to drawer front and locked in place by turning lever
Plinth fixing brackets (2 pcs)
White plastic, with 45 mm adjustment
- Runner fixing clip (2 pcs)
White plastic. To be fitted within drawer side either in 15/16 or 18/19 mm position
Spacers (4 pcs)
White plastic, 2 each 1 and 3 mm thickness included for use with runners where board thickness are other than 19 mm
Plinth feet (4 pcs)
Includes adaptors to fit underneath the cabinet sides
A deep drawer version can also be created when used in conjunction with railing 54539230

Gallery rails 400mm
Available in three sizes to make a standard drawer into a high sided drawer
For use with standard moulded plastic drawers or wooden drawers
Screw fixing
Back section changes to suit the drawer width, side sections are the same for all drawers
Chrome-plated steel

Gallery rails 500mm
Available in three sizes to make a standard drawer into a high sided drawer
For use with standard moulded plastic drawers or wooden drawers
Screw fixing
Back section changes to suit the drawer width, side sections are the same for all drawers
Chrome-plated steel

Gallery rails 600mm
Available in three sizes to make a standard drawer into a high sided drawer
For use with standard moulded plastic drawers or wooden drawers
Screw fixing
Back section changes to suit the drawer width, side sections are the same for all drawers
Chrome-plated steel

Sorto insert tray for cab 450mm
For 500 mm DWD drawer lengths and minimum cabinet width 450 mm
Consists of:
3 x Sorto inserts, 272 x 91 mm
3 x Sorto inserts, 1801 x 91 mm
1 x spacer 270 mm
1 x Divider support
Solid stainless steel/plastic

Sorto insert tray cab 600mm
For 500 mm DWD drawer lengths and minimum cabinet width 600 mm
Consists of:
3 x Sorto inserts, 270 x 90 mm
3 x Sorto inserts, 180 x 90 mm
1 x Sorto insert, 450 x 90 mm
1 x Sorto lid
1 x spacer 360 mm
1 x Divider support
Solid stainless steel/plastic

1 pair of base mounting drawer runners
25 kg capacity
Roller action; cabinet and drawer profiles have 1 plastic roller each
Self-closing
Epoxy coated steel
450mm installed length 340mm extension